Not all oils are created equal. So what are we looking for in a good Engine Oil for our Mazda Rx8?

1.  Lubrication of bearings, chain and internal engine moving parts

2.  Oil metering lubrication of combustion seals (apex, corner & side seals)

4.  Cooling of parts, in particluar rotors internally.

3.  Maintaining clean internal moving & stationary parts and oil galleries.

As an expert Mazda Rx8 engine builder, I am in the unique position to be able see and assess the consequences of customers using various engine oils and relating to engine wear, reliability and longevity.  One of the areas not very well understood is engine oil & lubrication.

Here are few case studies I have seen recently, with commentary illustrating why this subject is worth some attention.

Scott’s engine had only completed 83,019kms. Although still running, you can see the engine on the verge of catastrophic failure. The bearings were all failing due to either not enough and a poor quality oil or both. The crankshaft shows damage due to the lack of quality lubrication. This engine is likely to have been running oil levels too low too often with dirty old oxidised oil. Good quality oil will stay a good lubricant for longer. Consistently maintained higher oil levels also helps reduce degradation and "boil off" as well as diluting contaminants until they are removed by the oil filter.

Brett’s engine completed 140,313kms, shows significant bearing wear due to poor oil quality & low oil pressure. Although not the ultimate cause of engine failure, it would not have been long before crankshaft damage would have occured.  The ultimate cause of failure with this engine was excess carbon jammed into seals. As well as excess carbon, the engine had low compression from worn compression seals, poor starting, power and reliability.

Tom’s Rx8 Engine 189,794kms

Brett’s Rx8 Engine 140,313kms

Scott Rx8 Engine 83,019kms

Three examples;

Tom’s engine 189,794kms, Brett’s engine 140,313kms, and Scott’s engine 83,019kms. These examples show its not kilometres travelled that cause the majority of bearing wear. Tom’s engine had done 2.5 times as many kilometres as Scott’s yet the bearings are worn far less. We can see that longevity is achievable with factory Mazda bearings.  I suggest that the difference in oil quality and maintenance standards between Scott and Tom’s engine created the wide variation of bearing condition.

Scott’s Mazda Rx8 engine alloy front cover before the engine rebuild covered in sludge and varnish.

Tony’s Rx8 engine alloy front cover after running on Amsoil engine oil for almost 29,000kms in 3 years.

A good oil will not only be a good lubricant for a long period, but also maintain a cleaner environment inside and out of the engine, ensuring reduced wear rate of bearings and moving parts.

Scotts engine had completed only 83,019kms. When disassembled, I found severe oil sludge and varnish deposits and staining everywhere inside the engine. This is not un-common amongst engines having spent their lives using very average quality non-synthetic engine oil.

Tony’s front cover, pictured on the right, looks significantly different as he has used Amsoil for 3 years. Note there is no thick covering of sludge and varnish like Scott’s front cover. There has been a significant improvement using AMSOIL.

Scott’s Mazda Rx8 engine alloy front cover before the engine rebuild covered in sludge and varnish.

The Rx8 timing cover shown right has been acid dipped to remove all impurities. This is the ‘like new’ starting point used with every Mildren rebuilt engine. I am confident that Amsoil does not deposit sludge and varnish inside the engine. On the contrary, Amsoil will hold contaminants and particles in the oil until it passes through the engine oil filter, ensuring maximum removal of wear producing particles and contamination.

My experience and observations lead me to conclude:

  • It is important to use a Mazda Rx8 rotary compatible oil - AMSOIL is compatible.
  • A Mazda Rotary Rx8 compatible oil need not necessarily be specifically recommended by the Mazda Corporation.
  • A Mazda Rotary Rx8 compatible oil may be either petroleum based, semi-synthetic or fully synthetic, however,
  • Fully synthetic oils generally provide the best lubrication properties
  • Fully synthetic oils generally produce and deposit the least amount of sludge and varnishes inside engines

AMSOIL is Mazda Rotary compatible but most other fully synthetic oils are not compatible with Mazda Rx8 Engines.

My Recommendation; use the best quality Rx8 compatible oil you have access to. I use and recommend AMSOIL XLF1G 5W30 fully synthetic oil.

See Amsoil data sheet on Amsoil synthetic oil used in Mazda Renesis Rx8 Engines.

https://www.amsoil.com/techservicesbulletin/MotorOil/TSB%20MO-2007-09-06%20Mazda%20Rotary.pdf

Use a good engine oil and keep your insides clean!